Flex-Set
Plastic Coolant Hose Assemblies

STAYS PUT UNTIL YOU MOVE IT!
Bend it, twist it or tie it in a knot, FLEX-SET will stay put until YOU change it.  Glass smooth inside diameter promotes a clog-free full liquid flow at all times.  FLEX-SET will not rust or corrode, is impervious to sulpher base cutting oils.  Liquid and airtight because of one-piece construction.  Replaces all other types of coolant assemblies.

SPEEDS WORK SAVES MONEY!
KLING-FLO
Aerator Nozzle breaks up coolants into tiny bubbles which cling to the work and cover larger areas.  (See example in photo at left.)  While providing more rapid cooling it eliminates wheel-loading and permits faster working speeds.  Armored FLEX-SET gives steel braid protection to resist abrasion and the cutting action of hot chips and spiral shavings.  Higher working pressures are possible with Armored FLEX-SET.  

1. ...with OUTSIDE NOZZLE
New outside aluminum nozzle allows for greater resistance to wheel-wear and abrasion due to accidental contact with grinding wheels.  Because of its versatility this is one of the most popular styles of FLEX-SET.  Provides for use of FAN-FLO spout which changes the basic round stream into a flat fan-like ribbon of liquid which covers a wider work area.

2.  ...with INSIDE NOZZLE

Soft Aluminum tubing, inside nozzle allows for the forming or partial close-off and direction of the liquid to suit individual job requirements.

3.  ...with KLING-FLOW AERATOR NOZZLE

The aerator nozzle breaks up the coolant stream into millions of tiny oxygenated bubbles which cling to the work, eliminating splash and throw-off.  KLING-FLO increases emulsification and allows the water soluble coolant to dissipate heat more rapidly.  Eliminates wheel loading adn provides greater lubrication for minimum friction and wear on too. surfaces.  Results in longer tool life and less coolant waste.  Better work and more production is possible with KLING-FLO.

4.  ARMORED with OUTSIDE NOZZLE
Basic FLEX-SET assembly armored with steel braid covering offers long, trouble-free life.  Armor protects against the cutting action of hot chips and shavings.  The new outside aluminum nozzle allows for greater resistance to wheel-wear and abrasion due to accidental contact with grinding wheels.  Provides also for use of FAN-FLO spout to cover a wider working area.

5.  ARMORED with INSIDE NOZZLE

The steel braided armored FLEX-SET assembly armored with inside nozzle of soft aluminum tubing permits the forming or partial close-off and direction of the liquid flow to suit individual job requirements.  The armor conforms to the contour and bending radius of the basic FLEX-SET assembly and will stay put in any position.

6.  ARMORED  KLING-FLOW with AERATOR NOZZLE

Armored KLING-FLO with the aerator nozzle is unequalled in efficiency and long life.  The basic assembly described above (number 3) is improved by the addition of steel wire braid which gives added resistance to hot, sharp ships and shavings.  Armored KLING-FLO will stay where you put it and stay there until YOU move it.

FLEX-SET FOR EASY AND DEPENDABLE CONTROL OF COOLANTS & CUTTING LIQUIDS
SPECIAL LENGTHS & THREAD COMBINATIONS ARE AVAILABLE ON ORDER.
METAL ASSEMBLIES AVAILABLE ON SPECIAL ORDER

  Coupling Size IPT Length
Flex-Set Outside Nozzle O.S. 1/8" 6", 9", 12", 15", 18", 21", 24", 30", 36"
O.S. 1/4"
O.S. 3/8"
O.S. 1/2"
O.S. 3/4"
Flex-Set Inside Nozzle I.S. 1/8" 6", 9", 12", 15", 18", 21", 24", 30", 36"
I.S. 1/4"
I.S. 3/8"
I.S. 1/2"
I.S. 3/4"
Flex-Set Kling-Flo Aerator Nozzle KFNA - 616 3/8" 9", 12", 15", 18", 21", 24", 30", 36"
KFNA - 816 1/2"
KFNA - 1216 3/4"
Armored Flex-Set Outside Nozzle MALE 9", 12", 15", 18", 21", 24", 30", 36"
A.O.S. 1/4"
A.O.S. 3/8"
A.O.S. 1/2"
A.O.S. 3/4"
Armored Flex-Set Inside  Nozzle MALE 9", 12", 15", 18", 21", 24", 30", 36"
A.I.S. 1/4"
A.I.S. 3/8"
A.I.S. 1/2"
A.I.S. 3/4"
Armored Flex-Set Kling-Flo Aerator Nozzle KSFA - 616 3/8" IPT 9", 12", 15", 18", 21", 24", 30", 36"
KSFA - 816 1/2" IPT
KSFA - 1216 3/4" IPT

 


Full-Flo Stop-Cocks
Positive shut-off and full-flow.
Female thread both ends.
Install at inlet end of hose.

SIZES
1/8" 1/4" 3/8" 1/2" 3/4"

Next Product  

.

Cobon Plastics Corp
90 South Street
Newark, NJ  07114
Tel (973) 344-6330 • Fax (973) 344-6335
TOLL FREE (800) 360-1324
email:  cbco101@aol.com